อุปกรณ์วัดความดันแตกต่างชนิดเข็มที่มีย่านการวัดให้เลือกมากถึง 81 รุ่น และ 27 ตัวเลือก เกจวัดไม่มีแรงเสียดทานจึงตอบสนองได้อย่างรวดเร็ว วัดได้ทั้งแรงดันบวก แรงดันลบ และแรงดันแตกต่าง ตัวเกจถูกออกแบบมาตามมาตรฐาน IP67 ให้สามารถต้านทานแรงกระแทกของอากาศ ความสั่นสะเทือนและแรงดันเกินพิกัดได้ ความเที่ยงตรง คลาดเคลื่อนไม่เกิน 2%
Easy to read หน้าปัดมองเห็นง่ายจากระยะไกล
Quick response ตอบสนองรวดเร็วต่อการเปลี่ยนแปลงแรงดัน ทำให้ทราบทันทีหากพบความผิดปกติ
Durable ส่วนประกอบต่าง ๆ ของเกจมีคุณภาพสูง ทำให้เกจมีความทนทานยาวนาน หมดปัญหาเกจหยุดทำงาน
วัดสภาพของแผ่นกรองอากาศ (Filter Monitoring)
ใช้งานร่วมกับ Pitot tube เพื่อวัดความเร็วลม (Air Velocity)
วัดความดันหรือสูญญากาศค่าต่ำๆ
วัดความดันลบในห้องแยกโรค (Isolation room)
วัดความดันบวกในห้องปลอดเชื้อ (Clean room) หรือห้องผ่าตัด (Operating room)
Service: | Air and non-combustible, compatible gases (natural gas option available). Note: May be used with hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi. |
Wetted Materials: | Consult factory. |
Housing: | Die cast aluminum case and bezel, with acrylic cover, Exterior finish is coated gray to withstand 168 hour salt spray corrosion test. |
Accuracy: | ±2% (-HA model ±1) of FS (±3% (-HA ±1.5%) on -0, -100PA, -125PA, -10MM and ±4% (-HA ±2%) on -00, -60PA, -6MM ranges), throughout range at 70°F (21.1°C). |
Pressure Limits: | -20 in Hg. to 15 psig.† (-0.677 bar to 1.034 bar); MP option: 35 psig (2.41 bar), HP option: 80 psig (5.52 bar). |
IP67 |
|
Overpressure: | Relief plug opens at approximately 25 psig (1.72 bar), standard gages only. See Overpressure Protection note on Catalog page. |
Temperature Limits: | 20 to 140°F (-6.67 to 60°C). -20°F (-28°C) with low temperature option. |
Size: | 4" (101.6 mm) diameter dial face. |
Mounting Orientation: | Diaphragm in vertical position. Consult factory for other position orientations. |
Process Connections: | 1/8" female NPT duplicate high and low pressure taps - one pair side and one pair back. |
Weight: | 1 lb 2 oz (510 g); MP & HP 2 lb 2 oz (963 g). |
Standard Accessories: | Two 1/8" NPT plugs for duplicate pressure taps, two 1/8" pipe thread to rubber tubing adapters and three flush mounting adapterswith screws. (Mounting and snap ring retainer substituted for three adapters in MP & HP gage accessories.) |
Agency Approval: | Meets the technical requirements of EU Directive 2011/65/EU (RoHS II). Note: -SP models not RoHS approved. |
รายละเอียดสินค้า Catalog
คู่มือการใช้งาน (Eng) Instruction Manual
![]() |
|
![]() |
Name | |
---|---|
Model | |
แบรนด์สินค้า | |
Short Description |
There are no products matching the selection.
INDUSTRIAL ELECTRICAL CO., LTD.
© 2014 Copyright by ie.co.th . All Rights Reserved. |
GOOGLE MAP |
SITE MAP |
|